Messages

Code Select Expand


configure: error: Raspberry Pi API not found or incompatible with libCEC


I looked up, what exactly this is. In debian it would be libraspberrypi-dev. I think its the firmware. In arch linux it is the following package

Code Select Expand

# pacman -Q raspberrypi-firmware -i
Name           : raspberrypi-firmware
Version        : 20130116-1
URL            : https://github.com/raspberrypi/firmware
Licenses       : custom
Groups         : None
Provides       : raspberrypi-firmware
Depends On     : None
Optional Deps  : None
Required By    : libcec-rpi  xbmc-rbp-git
Conflicts With : raspberrypi-firmware
Replaces       : None
Installed Size : 48116.00 KiB
Packager       : Kevin Mihelich <kevin@archlinuxarm.org>
Architecture   : any
Build Date     : Wed Jan 16 21:50:04 2013
Install Date   : Tue Jan 22 15:14:41 2013
Install Reason : Explicitly installed
Install Script : No
Description    : Firmware files for Raspberry Pi


An actual version

Without patching the vompclient sources the compile should not have succeeded if the libcec version is greater than 2.0.
Perhaps a stray version is picked up while compiling.

OMG, i new it. 

Probably the libcec version is the problem. The interface was changed with version 2.0.
The development of vomp is with a version below 2.0, it is 1.8.1.

Marten

Will there be an update in the near future? Because downgrading isn't a simple act, I'ld consider to wait for a new version. Actualy I'm using a workaround of omxplayer and streamdev.

Code Select Expand


configure: error: Raspberry Pi API not found or incompatible with libCEC


Hi Marten

This is the log of vompclient running in debug modus.
About libcec. I've installed libcec-rpi 2.0.5.

Code Select Expand

# cec-client -i
libCEC version: 2.0.5, host: armv6l-unknown-linux-gnueabihf, features: 'P8 USB' 'P8 USB detect' 'RPi', compiled on: Fri Dec 21 18:08:40 UTC 2012 by nobody@panda3 on Linux 3.2.34-1-FARM (armv6l

Hello everybody

I'm unable to get vompclient and server connected. I'm running this setup:
A Server with TV-Card. Ubuntu 12.04.01

Code Select Expand

$ uname -rv
3.2.0-37-generic-pae #58-Ubuntu SMP Thu Jan 24 15:51:02 UTC 2013
$ vdr --version
vdr (1.7.27/1.7.27) - The Video Disk Recorder
femon (1.7.17) - DVB Signal Information Monitor (OSD)
xvdr (0.9.8) - XVDR Server
live (0.2.0) - Live Interactive VDR Environment
vompserver (0.4.0) - Vompserver plugin by Chris Tallon
vnsiserver (0.9.0) - VDR-Network-Streaming-Interface (VNSI) Server


And a Pi with Arch Linux as Client

Code Select Expand

# uname -rv
3.6.11-4-ARCH+ #1 PREEMPT Wed Jan 16 19:06:54 UTC 2013


both vompserver and client are compiled from git
server is 0-4-0rc and client is master branch.

When I start vompclient it turns on, connects to the VDR Server and stops with Segmentation fault.
Stacktrace from vompclient
Log of Server while client is connecting.

Also I did some modifications to the Makefile to build it on Arch Linux. Hopefully this isn't breaking anything...

I can't see a failure, but I have to confess not to be a good trace reader. I'm realy not sure about all the config errors, though

Any help? Can you point me in the right direction?

Greetings